Katana
Noritake™ Katana Multi-Layer Zirconia STML
Customer Reviews
- Reviews
- Questions
- color match
- turnaround
- rush case
- seating
- Value
- MENLO PARK
- PARRAVI
- zero
- milling center
- myou guys mill HTML
Bubbles
End product came out good but we had to do some repairs, lower arch had some tiny bubbles that we repaired with porcelain.
United StatesPerfect fit
The service was very straight forward and the bridge was designed and milled perfectly. I will definitely continue to use the service and recommend it to others.
United StatesMixed results
The fit and the milling are both 5*. The translucency is extremely opaque only 1*. Not sure why but the lingual had better shade esthetics than the facial. There also is a very opaque ring around the margin going up the axial wall approximately 1mm that is not even close to the desired shade. Shade not anywhere close to the prescribed D3. We have used this product in the past and the material was not this opaque. Very disappointed.
United Statesunable to seat without a jig
The crown is pretty but it is difficult to seat the crown and abutment in separate pieces. I think I asked for screw retained but did not get that. I did place the implant lingually so we could create a screw retained
United States
Overhang
Please fabricate crowns as instructed. Finish margins are too thick causing overhang.
Share this Product
Other great brands
QUESTIONS & ANSWERS
Ask a Question-
Is it necessary for me to design the crown? Can I send you the STL of the prepared tooth only?
No it is not neccesary. You can send the STL Files of the scan for a design service here.
Dental CAD Design Service
Then add a "Milling Service" crown of your choice.
Note:
Ensure the "Case ID" on the Design Prescription and Milling Prescription are identical. -
So do you guys make/mill the crown with a tooth model or do you guys just sell the block
Both
-
Can Katana be a c2 shade?
We decided to launch the STML Line of Katana which only carried Shades A1-A4 and NW.
-
Can you mill a Katana screw-retained implant bridge with access holes?
We can but it is not recommended.
The implant crowns recommended can be found here.
https://www.alienmilling.com/collections/implant-crown -
I have a maryland bridge to be milled in katana. its one pontic and 2 flanges. How much will that be?
That will be considered 3 units.
Please place an order with 3 units. -
I am going to order twelve zirconia crowns with upload stl. I am a biginner of CAD. can you check my design and show your opinion for good crown? And does "no finishing" mean after sintering?
Hi there,
We will check the mill quality of your restorations after mill, and if we see any issues, our Customer Service Team will get in touch with you.
No Finishing means no Stain and Glaze after sinter. -
What is the strength of this product
748Mpa
-
I've noticed for the Full Arch Hybrid cases you give the option of shipping back in the green state. Do you offer this option for single zirconia crowns? If not, why?
Green State is only available for Full Arch Hybrid as of June 7 2019.
We haven't received many requests for single crowns in green state compared to full arch cases.
We will add you request to offer single crowns in the Green State.
Thanks for reaching out to us. -
we need to upload both upper and lower files. It is only giving us the option to upload 1 and not both.
You would need to click on "Upload Jaw Scans - Design Service"
-
Do you send back to the labs just sintered or finisned?
If ordered without finishing, it is just sintered. If ordered with Stain and Glazed, then we finish the crown.
-
can i have cut back crown .
Our cutback crowns can be found here.
https://www.alienmilling.com/collections/3-4-solid-zirconia-crown-for-facial-porcelain-layering/products/3-4-zirconia-crown